Facile high yield synthesis of MgCo2O4 and investigation of its role as anode material for lithium ion batteries

In this article, we have reported a one-step scalable synthesis of MgCo₂O₄ nanostructures as efficient anode material for Li-ion batteries and investigated the role of post-synthesis calcination temperature (400, 600 and 800 °C) on its physiochemical properties and electrochemical performances. The XRD pattern of the calcinated sample at 400 °C (MC 400) indicates a pure phase of MgCo₂O₄. However, on increasing the calcination temperature to 600 °C (MC 600), an additional phase corresponding to MgO was detected and the corresponding XRD peak intensity further increased on increasing the calcination temperature to 800 °C (MC 800 °C). This was accompanied by a morphological transformation from flake and rod-like nanostructures, to an agglomerated dense flake-like morphology. Electrochemical studies revealed that the calcination temperature plays an important role in determining the electrochemical performance of the MgCo₂O₄ as anode material. In a half cell, the MC 600 showed the best electrochemical performance with high discharge capacity of 980 mA h g⁻¹ (2nd discharge at 60 mA g⁻¹) and a reversible discharge capacity of 886 mA h g⁻¹ at the end of 50 cycles with high coulombic efficiency of 98%. Long term stability was carried out at 0.5C which showed a capacity retention of 358 mA h g⁻¹ at the end of 500 cycles. The superior electrochemical performance of the MC600 can be attributed to the presence of the small amount of MgO, which is believed to provide the anode materials better structural stability during cycling. The claim was further supported by ex-situ TEM analysis of the anode material of a cycled cell (50 cycles).     

Alkali metal ion substitution induced luminescence enhancement of NaLaMgWO6:Eu3+ red phosphor for white light-emitting diodes

Alkali metal ion substitution is an effective strategy to improve the luminescence properties of phosphors. In this work, a series of red-emitting phosphors Na_1-xLi_x/2K_x/2La_0.6Eu_0.4MgWO₆ were prepared by a traditional high-temperature solid-state reaction. Their phase structure, microstructure, luminescence properties and potential application in phosphor-converted white light-emitting diodes (pc-WLEDs) were investigated in detail. X-ray diffraction (XRD) result revealed the formation of a solid solution when x?≤?0.3, which kept monoclinic structure of NaLaMgWO₆. Photoluminescence investigation indicated that the partial substitution of Li⁺/K⁺ ions for Na⁺ ions improved largely the red emission of Eu³⁺. Based on the optimized Na_0.7Li_0.15K_0.15La_0.6Eu_0.4MgWO₆ sample with relatively good thermal stability, a WLED device was fabricated by combining a near-ultraviolet (NUV) chip (~400?nm) with the phosphor mixture of commercial green/blue phosphors and the optimized red phosphor. The results indicated that the optimized red phosphor in this work could be a potential candidate for WLEDs pumped by NUV chips.     

Spreading and Curing Behaviors of a Thermosetting Droplet-Silicone on a Heated Surface

Thermosetting materials are widely used as encapsulation in the electrical packaging to protect the core electronic components from external force, moisture, dust, and other factors. However, the spreading and curing behaviors of such kind of fluid on a heated surface have been rarely explored. In this study, we experimentally and numerically investigated the spreading and curing behaviors of the silicone(OE6550 A/B, which is widely used in the light-emitting diode packaging) droplet with diameter of ～2.2 mm on a heated surface with temperature ranging from 25 ℃ to 250 ℃. For the experiments, we established a setup with high-speed camera and heating unit to capture the fast spreading process of the silicone droplet on the heated surface. For the numerical simulation, we built a viscosity model of the silicone by using the Kiuna's model and combined the viscosity model with the Volume of Fluid(VOF) model by the User Defined Function(UDF) method. The results show that the surface temperature significantly affected the spreading behaviors of the silicone droplet since it determines the temperature and viscosity distribution inside the droplet. For surface temperature varied from 25 ℃ to 250 ℃, the final contact radius changed from ～2.95 mm to ～1.78 mm and the total spreading time changed from ～511 s to ～0.15 s. By further analyzing the viscosity evolution of the droplet, we found that the decreasing of the total spreading time was caused by the decrease of the viscosity under high surface temperature at initial spreading stage, while the reduction of the final contact radius was caused by the curing of the precursor film. This study supplies a strategy to tuning the spreading and curing behavior of silicone by imposing high surface temperature, which is of great importance to the electronic packaging.     

Synthesis of highly active and stable Pd/C catalysts toward HCOOH dehydrogenation by a simple NH3 adsorption method

Pd catalysts supported on activated carbon (Pd/C–NH₃) toward HCOOH dehydrogenation were prepared by a simple adsorption method using ammonia (NH₃) and Ar as the working gas. The results show that the TOF_initial of Pd/C–NH₃ was 459.8 h⁻¹ at 50 °C. When the reaction was carried out for 4 h, the HCOOH dehydrogenation ratio over Pd/C–NH₃ was about 81.2%, which was 1.15 and 1.13 times, respectively, as that of the as-prepared Pd/C catalyst without any treatment (Pd/C–As) and the Pd/C catalyst purchased from Sigma-Aldrich (Pd/C-CM). The total amount of H₂ and CO₂ produced by using Pd/C–NH₃ to decompose HCOOH in the third cycle was 99.4% of the gas produced by the first reaction cycle, and 1.80 and 12.60 times, respectively, as that of Pd/C–As and Pd/C-CM. The characterization results indicated that the Pd active species in Pd/C–NH₃ migrated to the outer surface of the carbon support during the reaction, and the pore volume of the carbon support became larger, which were beneficial to the reaction. These factors made Pd/C–NH₃ exhibit excellent HCOOH dehydrogenation activity and stability. NH₃ adsorption is a simple and effective method for preparing high-performance Pd/C HCOOH dehydrogenation catalysts, and has important guiding significance for the preparation of other carbon supported noble metal catalysts.     

Contribution of metal vapor mass at periphery part of pulsed arc to electromagnetic force in weld pool

The arc welding has been used in various welding methods because it is inexpensive and high in strength after welding. However, it is a problem that accidents such as collapse of the bridge occur because of the welding defects. The welding of low cost and high productivity is required without the welding defects. The pulsed TIG welding is inexpensive and capable of high‐quality welding. The electromagnetic force contributing to penetration changes because the transient response of arc temperature and iron vapor generated from anode occurs. However, the analysis of pulsed TIG welding with metal vapor has been elucidated only metal vapor concentration near anode with transient phenomenon and heat flux. Thus, the theoretical elucidation of penetration depth with control factor has not been researched. In this paper, the contribution of metal vapor mass at the periphery part of pulsed arc to the electromagnetic force in the weld pool is elucidated. As a result, the iron vapor mass at periphery part decreased with increasing the frequency. The iron vapor was stagnated at axial center within one cycle. The electromagnetic force to the penetration depth direction in weld pool increased at axial center. Therefore, the metal vapor mass at periphery part plays an important role for the electromagnetic force increment at axial center.     

Promoted electrocatalytic hydrogen evolution performance by constructing Ni12P5–Ni2P heterointerfaces

Transition metal phosphides (TMPs) have been considered as cheap alternatives of precious metal platinum for electrochemical hydrogen evolution reaction (HER). In the past decades, many reports have indicated that the engineering of heterointerfaces between different components could efficiently enhance the activity of HER catalysts. Here, we report a facile method to construct Ni₁₂P₅–Ni₂P heterostructure by using a low temperature phosphorization strategy. The obtained Ni₁₂P₅–Ni₂P heterostructure shows high activity toward HER with an overpotential value of 166 mV at 10 mA cm^?2 and a Tafel slope of 60 mV dec^?1 in 0.5 M H₂SO₄. Compared with pure Ni₂P and Ni₁₂P₅, the Ni₁₂P₅–Ni₂P heterostructure has more active sites and faster HER kinetics due to the presence of the interfaces between Ni₁₂P₅ and Ni₂P. Furthermore, we used the obtained Ni₁₂P₅–Ni₂P as cathodic catalyst and IrO₂/Ti as anodic material to set up a proton exchange membrane (PEM) electrolyzer which shows good stability after 120 h continuous constant current electrolysis at 200 mA cm^?2. This work demonstrates the positive effect of heterostructure for HER catalysts and provides a feasible strategy for constructing earth-abundant electrocatalysts.     

Laser-assisted preparation of monolithic acidic catalysts for biomass conversion

5-(Hydroxymethyl)furfural (5-HMF) is a vital platform molecule from which a variety of high-value-added fine chemicals and polymerizable monomers can be prepared. The use of solid acids to catalyze the conversion of biomass into 5-HMF is environmentally friendly and economical. However, exploiting the high yield of 5-HMF in a highly concentrated reactant system is challenging. Herein, we present a laser-assisted method for preparing highly acidic monolithic acidic catalysts. A monolithic acidic catalyst based on metal Zr sheets was synthesized and used to catalytically convert 30 wt% fructose into 5-HMF (conversion rate: 96%; yield: 95%). The catalyst was immediately separated from the reaction solution by direct removal at the end of the reaction. Catalytic efficiency was largely unaffected after 10 cycles of use, and the same catalytic efficiency was observed after laser-regeneration, highlighting the potential industrial applicability of the developed catalyst.     

High ultraviolet transparent conducting electrodes formed using tantalum oxide/Ag multilayer

We investigated the optical and electrical properties of Ta₂O₅/Ag/Ta₂O₅ films as functions of the thicknesses of the Ta₂O₅ and Ag layers. It was found that with an increase in the thicknesses of the Ta₂O₅ and Ag layers from 10 to 40 nm and from 12 to 24 nm, respectively, the sheet resistance, carrier concentration, electron mobility, and resistivity of the Ta₂O₅/Ag/Ta₂O₅ film varied from 2.02 to 8.95 Ω/sq, 5.74 × 10²¹ to 2.92 × 10²² cm^–3, from 13.21 to 24.07 cm²/V·s, and from 8.89 × 10^-6 to 8.24 × 10^-5 Ω cm, respectively. The average transmittance (T_av) of the multilayer samples ranged from 57.18% to 93.99%, and it depended on the Ta₂O₅ and Ag layer thicknesses. The highest T_av of 93.99% was observed for the film with 35 nm thick Ta₂O₅ and 18 nm thick Ag layers, and the peak Haacke's figure of merit (157.04 × 10^–3 Ω^–1) was obtained for 20 nm thick Ta₂O₅ and 21 nm thick Ag layers. Ta₂O₅ (100 nm) and Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) samples had optical bandgaps of 4.70 and 4.45 eV, respectively. Film Wizard simulations were conducted to understand the dependence of the transmittance of the multilayer on the thicknesses of the Ta₂O₅ and Ag layers, and phasor analyses were performed to determine how the transmittance of the Ta₂O₅/Ag/Ta₂O₅ (20 nm/21 nm/20 nm) film depended on the Ta₂O₅ layer's thickness.     

Effect of sintering temperature on solidification and migration of non-volatile and volatile heavy metals in glass-ceramic

Using tailings as material to prepare glass-ceramic is an excellent way to achieve the resource utilization of solid waste. However, at present, researches on the solidification and migration of heavy metals are limited. Therefore, in this study, ten groups of samples were prepared by controlling sintering temperatures. The solidification, migration, and leaching behavior of non-volatile and volatile heavy metals were studied. The research showed that, with the increase of temperature, the properties of the samples were improved. Fe participated in the phase transformation and evolved into insoluble iron pyroxenes solid solution, while Pb was homogeneously distributed in the glass matrix of glass-ceramics. The leaching concentrations of Fe and Pb in the glass-ceramics were 0.055 mg/L ～0.087 mg/L and 0.074 mg/L ～0.140 mg/L, which were far below the threshold value. The results showed that heavy metals can be effectively solidified in glass-ceramics and have good environmental benefits.     

Vacancy-engineered V2O5-x films for ultrastable electrochromic applications

In the present study, we prepared vacancy-engineered V₂O_5-x films for electrochromic (EC) applications. To investigate the vacancy effect of V₂O_5-x films with high EC performance capabilities, precursor concentrations of V-based sol solutions were varied at 1 wt%, 5 wt%, and 10 wt%. Among them, V₂O_5-x films with a precursor concentration of 5 wt% (V₂O₅-5wt%) showed superior EC performance outcomes due to the (001)-plane-oriented crystal structure, which provides high electrical conductivity with the oxygen vacancy (V_o). In addition, the gravel-like uniform surface morphology with the optimized film thickness provides a stable electrochemical reaction during the EC measurement. As a result, V₂O₅-5wt% exhibited fast switching speeds (2.1 s for coloration and 3.6 s for bleaching), high transmittance modulation (ΔT) (51.32%), high coloration efficiency (CE) (52.3 cm²/C), and excellent cycle stability (85.85% ΔT retention after 500 cycles). In addition, V₂O₅-5wt% showed energy storage capability of 443.7 F/g at a current density of 2 A/g, thus proving its potential for use in multi-functional applications. Therefore, these results provide valuable insight related to the engineering of vacancies in EC films to achieve high-performance EC devices and additional multi-functional applications.